60x100 Metal Building: 2026 Cost And Uses
A 60x100 metal building gives you 6,000 square feet under one roof, with a 60 foot clear span and no interior columns. It's one of the most popular sizes for small warehouses, contractor shops, agricultural buildings, churches and indoor sports. In 2026, a basic 60x100 kit typically costs about $84,000 to $102,000, and a finished turnkey building usually runs $180,000 to $270,000.
Here's what goes into that price, what the building is used for, and what to plan for the foundation.
60x100 Metal Building Price
| Item | Cost per sq ft | 60x100 (6,000 sq ft) |
|---|---|---|
| Kit (frame, roof, walls, trim) | $14 to $17 | $84,000 to $102,000 |
| Erection labor | $4 to $12 | $24,000 to $72,000 |
| 4 inch concrete slab | $5 to $9 | $30,000 to $54,000 |
| Turnkey total | $30 to $45 | $180,000 to $270,000 |
These ranges match our metal building prices research. Your price depends on eave height, design loads for your area, doors, windows, insulation and how far the building ships. For a quick estimate on your own options, use the metal building cost calculator.
What changes the price
- Eave height. Taller walls use more steel. A 14 to 16 foot eave is common for shops and warehouses; 20 feet or more for racking, cranes or tall equipment.
- Loads. Heavy snow or high wind areas need heavier frames and closer purlin spacing.
- Frame type. Clear span costs more than a modular frame with interior columns at this width, but gives you open floor space.
- Doors. Large roll up or framed openings need extra framing. Each 14x14 overhead door adds to the cost.
- Insulation and liner panels. Needed for conditioned space.
- Steel prices. Kit prices follow steel. See our metal building price index for current trends.
Common Uses
| Use | Typical setup |
|---|---|
| Warehouse and storage | 16 to 20 ft eave, several roll up doors, a small office |
| Contractor or fleet shop | 16 ft eave, drive through doors, heated bays |
| Agricultural building | Equipment storage, hay, livestock, open or enclosed sides |
| Church or event hall | Clear span sanctuary with lobby, restrooms and classrooms |
| Indoor sports | Batting cages, pickleball, training, with taller eaves |
| Retail or showroom | Storefront with glass, office and storage area |
| Shop with living quarters | Large shop with an apartment section |
6,000 square feet is enough for a small distribution or storage operation, a two or three bay truck shop, or a church with seating for a few hundred people. For more on commercial storage space, see our warehouse building costs guide, and our metal church buildings guide for congregations.
Clear Span Options
At 60 feet wide, you can choose a clear span frame with no interior columns or a modular frame with one row of columns down the middle.
| Frame type | Pros | Cons |
|---|---|---|
| Clear span | Fully open floor, easy to lay out, best for equipment and sports | More steel in the frames, higher kit cost |
| Modular (one interior column line) | Lighter frames, lower kit cost | Columns in the floor, limits layouts |
Most buyers at this size go with clear span, since open floor space is the main reason to buy a steel building. Modular frames make more sense for much wider buildings, like 100x120 and larger. See our 100x120 metal building page for that size.
Roof pitch
A 1:12 roof pitch is standard for many commercial steel buildings. A steeper 3:12 or 4:12 pitch sheds snow better and looks more like a barn or house, but adds height and cost. In heavy snow areas your engineer may recommend a steeper roof.
Bay spacing
A 100 foot long building is usually divided into bays of 20 to 25 feet, for example four bays of 25 feet or five bays of 20 feet. Bay spacing affects where you can put doors, since large doors usually go between frames.
Foundation
A 60x100 building usually sits on a concrete slab with thickened edges and deeper footings at each column. Because the frames are clear span, each column puts significant loads into the ground, including outward thrust and wind uplift. The foundation has to be designed for the column reactions on your building drawings.
A 4 inch slab of 6,000 square feet needs about 74 cubic yards of concrete, or about 81.5 with a 10% waste allowance. At around $174 per cubic yard, the concrete alone costs about $14,200, before labor, reinforcement, vapor barrier and finishing. A 6 inch slab, common for heavy trucks or equipment, needs about 50% more concrete.
| Slab thickness | Cubic yards (with 10% waste) | Concrete at $174 per yd |
|---|---|---|
| 4 inch | 81.5 | About $14,200 |
| 5 inch | 101.9 | About $17,700 |
| 6 inch | 122.2 | About $21,300 |
Try our concrete slab calculator for your own thickness and finish, and read the metal building foundation guide for foundation types and anchor bolts.
Doors, Windows And Options
| Option | Notes |
|---|---|
| Roll up doors | Common sizes 10x10 to 16x16 for trucks and equipment |
| Framed openings | For sectional or hangar style doors |
| Walk doors | At least one per exit requirement; commercial buildings need more |
| Windows | Office areas and natural light |
| Skylights or light panels | Daylight for large open spaces |
| Insulation | Faced blanket, insulated panels or spray foam |
| Lean to | Covered storage or parking along a side wall |
| Mezzanine | Office or storage space above part of the floor |
Planning door locations early matters. Doors in the end walls are easiest, while large side wall doors need careful framing between columns. Our insulation calculator helps estimate insulation cost for the walls and roof.
Planning The Layout
With 6,000 square feet you can fit a lot, but a little planning goes a long way. A few layout ideas:
- Shop plus office. Put a 20x30 office, restroom and break room at one end and leave about 5,400 square feet of open shop.
- Truck bays. Three or four drive in bays along one side wall, each with a 14 foot or 16 foot door, and storage at the back.
- Warehouse. Pallet racking along the side walls with a central aisle, a dock door at one end and a small office near the entrance.
- Mixed use. Rent out part of the building as storage units while you use the rest.
Think about how vehicles and forklifts will move in and out, where you'll need power and water, and whether you might expand later. A building can be designed with an expandable end wall so you can add length in the future, for example growing to 60x140.
Running Costs
A large open building costs money to heat and cool. Insulation, airtight doors and the right heating system make a big difference. Many shops use radiant tube heaters or unit heaters hung from the frame, while offices and living areas use standard HVAC. Painted steel roofs and walls need little upkeep, but plan for gutters, sealants and door maintenance.
Permits
A 6,000 square foot building almost always needs a building permit, and commercial use adds requirements for exits, fire protection, accessibility and parking. Your supplier should provide engineered drawings stamped for your state. See our metal building permits guide for the process.
Saving Money On A 60x100
- Keep the eave height to what you really need. Every extra foot adds steel.
- Standardize door sizes and place them in end walls where possible.
- Get several quotes with the same size, loads and options so you can compare them fairly.
- Do some work yourself, such as site prep or finishing, if you have the skills.
- Order when steel is stable and lock in the price with a deposit.
Get Quotes
Ready to price your building? Get free quotes from suppliers for a 60x100 with your options.
FAQ
How much does a 60x100 metal building cost?
A basic 60x100 kit costs about $84,000 to $102,000 in 2026. A finished turnkey building with erection and a slab usually runs $180,000 to $270,000.
How much concrete do I need for a 60x100 slab?
About 74 cubic yards for a 4 inch slab, or about 81.5 with 10% waste.
Can a 60x100 building be clear span?
Yes. A 60 foot clear span is very common and gives you an open floor with no interior columns.
How long does it take to put up a 60x100 metal building?
Once the slab is cured and the kit is delivered, an experienced crew can often erect the shell in a few weeks. Ordering, engineering, permits and the foundation usually take longer than the erection itself.
What is a 60x100 building used for?
Warehouses, contractor shops, farm buildings, churches, indoor sports facilities and retail spaces are all common uses.
Ready to price your building? Get free metal building quotes from suppliers who serve your area, or use the form on this page and our team will be in touch.